Design of girth welding system based on tungsten inert gas welding

نویسندگان

چکیده

This article studies the multi-layer and multi-pass welding of circumferential weld in thick pipe an aviation enterprise, based on static characteristics arc, through data calculations experiments to verify relationship between arc voltage length, proposes use controller accurately adjust real time, improve stability, torch wiggler expand fusion width, meet adaptive adjustment wide weld, build main control system programmable logic (PLC) control. Integrating all subsystems put them into actual production significantly improves efficiency parts welding, reduces defects, quality parts.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

The principle Of Tungsten Inert Gas (TIG) Welding Process

Process This chapter presents the principle of tungsten inert gas (TIG) welding process besides important components of TIG welding system and their role. This process is also known as gas tungsten arc welding (GTAW) process. Further, fundamentals of heat generation, arc stability and arc efficiency have also been described. Additionally, comparison of argon and helium as shielded gases has bee...

متن کامل

Gas tungsten arc welding

Gas tungsten arc welding (GTAW), also known as tungsten inert gas (TIG) welding, is an arc welding process that uses a nonconsumable tungsten electrode to produce the weld. The weld area is protected from atmospheric contamination by a shielding gas (usually an inert gas such as argon), and a filler metal is normally used, though some welds, known as autogenous welds, do not require it. A const...

متن کامل

Welding of 304L Stainless Steel with Activated Tungsten Inert Gas Process (A-TIG)

Gas tungsten arc welding is a popular process in those applications requiring a high degree of quality and accuracy. However, this process has a big disadvantage against the substantially high productivity welding procedures. Hence, many efforts have been made to improve its productivity. One of these efforts is the use of activating flux (A-TIG welding). In this study, the performance of A-TIG...

متن کامل

Structure-property Interaction in Flux Assisted Tungsten Inert Gas Welding of Austenitic Stainless Steel

Austenitic stainless steel SS304 grade was welded with active Tungsten Inert Gas (TIG) welding process by applying a flux paste made of SiO2 powder and acetone. SiO2 flux application improves the weld bead depth with a simultaneous reduction in weld bead width. The improvement in penetration results from arc constriction and reversal of Marangoni convection. Experimental studies revealed that t...

متن کامل

Hot cracking in tungsten inert gas welding of magnesium alloy AZ91D

Plates of 3–5 mm in thickness were extracted from an AZ91D ingot and then butt joints of the plates were produced using tungsten inert gas (TIG) welding method. The TIG arc was also used to deposit welding beads on some of the thin plates. No cracking was found in the butt joints. However, hot cracking was always observed to propagate from the heat affected zone (HAZ) under the welding bead int...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ژورنال

عنوان ژورنال: International Journal of Advanced Robotic Systems

سال: 2023

ISSN: ['1729-8806', '1729-8814']

DOI: https://doi.org/10.1177/17298806231181966