Crack study of recasting layer on workpiece surface in Micro-EDM
نویسندگان
چکیده
In this paper, the crack phenomenon of different materials was studied according to surface morphology recasting layer micro EDM workpiece. high-speed steel and titanium alloy are used as workpiece materials, RC pulse power supply is for electric discharge machining. The profile recast examined by scanning electron microscopy. difference between two in spark machining analyzed. Finally, some improvement measures put forward solve problem on
منابع مشابه
Effect of low-frequency vibration on workpiece in EDM processes
High-frequency vibration aided EDM has become one of the ways to increase material removal rate in EDM process, due to the flushing effect caused by vibration. However, utilizing high-frequency vibration, especially in ultrasonic range consumes a lot of setup cost. This work presents an attempt to use a low-frequency vibration on workpiece of stainless steel (SS 304) during EDM process. The wor...
متن کاملeffect of the micro wire-edm process parameters on the recast layer in the molybdenum micromachining
the micro wire electrical discharge machining (micro wire-edm) process is a modern machining process with various applications in manufacturing micro-parts. the recast layer remaining on the machined surfaces is an inevitable complication of this process. this layer can subsequently affect the machined parts performance. to optimize the recast layer in the micro wire-edm of the molybdenum micro...
متن کاملthe study of bright and surface discrete cavity solitons dynamics in saturable nonlinear media
امروزه سالیتون ها بعنوان امواج جایگزیده ای که تحت شرایط خاص بدون تغییر شکل در محیط منتشر می-شوند، زمینه مطالعات گسترده ای در حوزه اپتیک غیرخطی هستند. در این راستا توجه به پدیده پراش گسسته، که بعنوان عامل پهن شدگی باریکه نوری در آرایه ای از موجبرهای جفت شده، ظاهر می گردد، ضروری است، زیرا سالیتون های گسسته از خنثی شدن پراش گسسته در این سیستم ها بوسیله عوامل غیرخطی بوجود می آیند. گسستگی سیستم عامل...
A Review of Micro - EDM
There is a huge demand in the production of microstructures by a non-traditional method which is known as Micro-EDM. Micro-EDM process is based on the thermoelectric energy between the workpiece and an electrode. Micro-EDM is a newly developed method to produce micro-parts which in the range of 50 μm -100 μm. Micro-EDM is an efficient machining process for the fabrication of a micro-metal hole ...
متن کاملMICRO-EDM FOR MICRO-CHANNEL FABRICATION ON NONCONDUCTIVE ZrO2 CERAMIC
In this study, microelectro-discharge (micro-ED) milling of nonconductive ZrO2ceramicsis investigated using a Cu tool electrode in kerosene dielectric. An adhesive Cu foil is firmly attached on the workpiece to initiate the sparks. After the machining of Cu foil, an electrically conductive carbonic layer is formed on the ceramic workpiece disassociating the kerosene dielectric, which allows mic...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: MATEC web of conferences
سال: 2022
ISSN: ['2261-236X', '2274-7214']
DOI: https://doi.org/10.1051/matecconf/202236301011