Anisotropy of Damping Capacity of 42 wt%Mn-2 wt%Al-Cu Alloy Sheet
نویسندگان
چکیده
منابع مشابه
DAMPING CAPACITY AND MECHANICAL PROPERTIES OF Zn-Al ALLOY CASTINGS
This paper describes damping capac i t y and mechanical p roper t ies o f Zn-8-20%A1 and Zn-8-20%Al-0.02-0.04XMg a l l o y cast ings. Zn-8-20%A1 a l l o y casti ngs show h igh damping when quenched from 573K. Small amount o f Mg a d d i t i o n t o these a l l o y cast ings lowers damping capaci ty considerably b u t e f f e c t i v e t o reduce decomposition through aging a t 423K f o r 48hrs ...
متن کاملPSEUDOELASTIC BEHAVIOR OF COIL SPRING MADE OF A HIGH-DAMPING Cu-Zn-Al ALLOY
2. Experiment,aZs A c o i l s p r i n g w i t h a f r e e l e n g t h o f 100 mm a t 20°C and an average d i a m e t e r o f 16 mm w i t h e f f e c t i v e number o f t u r n o f 23 was s u p p l i e d by P r o t e u s (F4e ta l lu rg i e Hoboken-Overpel t , Hoboken and N . V . B e k a e r t S .A . , Zwevegem, i n c o o p e r a t i o n w i t h K a t h o l i e k e U n i v e r s i t e i t L e u ...
متن کاملEBSD Characterization of the Twinning Microstructure in a High-Damping Mn--Cu Alloy
The {101} transformation twinning bands in Mn–Cu alloys are considered to be the dominant microstructural feature contributing to the high damping capacity of the alloys. Because the face-centered-tetragonal (fct) phase of Mn–Cu alloys has an axis ratio ðc=aÞ of nearly 1, an angular resolution for Kikuchi diffraction bands of better than 0.5 is necessary to identify the twin boundaries by the e...
متن کاملEffect of Aging Treatment on the Damping Capacity and Mechanical Properties of Mg-6Al-1Zn Alloy
The damping capacity and mechanical properties of Mg-6Al-1Zn alloy after heat treatment were investigated. The damping characteristics of un-heat-treated, solution treated, and aged Mg-6Al-1Zn specimens were determined by measuring the damping ratio and the logarithmic decrement of free vibrations of a bending beam clamped at one side. The microstructural evaluations confirmed that the β-Mg17Al...
متن کاملEffects of Alloying Elements on Martensitic Transformation Behavior and Damping Capacity in Fe-17Mn Alloy
Effect of carbon and Ti on 7-s martensitic transformation behavior and damping capacity has been investigated in an Fe-17Mn alloy. The suppressive force of carbon against 7-s transformation increases linearly with an increase in carbon content, lowering M, temperature and volume fraction of s martensite. Carbon deteriorates damping capacity by reducing the area of y l e interfaces and by decrea...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Journal of the Japan Institute of Metals and Materials
سال: 1981
ISSN: 0021-4876,1880-6880
DOI: 10.2320/jinstmet1952.45.1_1