An Al-12Si/ZnS powder inoculant for eutectic silicon in Al-12Si alloy

نویسندگان

چکیده

To obtain high-performance Al-Si-based cast alloys, refinement and modification of Si phases are required. An Al-12Si/ZnS powder inoculant was designed fabricated using a chemical bath deposition method. The efficiency the for modifying eutectic phase in as-cast Al-12Si alloy studied. Results show that can significantly refine Al-Si alloys. best effect is achieved with 17.5wt.% powder. Coarse long needle-shaped length 18 µm modified into approximately spherical shape diameter 6.53 µm, which evenly distributed throughout alloy. E2EM model calculation indicates inter-plane misfit (Fp) inter-atomic spacing (Fr) between ZnS all less than 0.5%, confirms potential nucleation site phase. hardness, tensile strength, elongation alloys 17.5% increase 6.30%, 16.18% 55.45%, respectively, compared to unmodified fracture behavior dominated by transgranular supplemented intergranular fracture.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Production of silicon carbide Al 2124 alloy functionally graded materials by mechanical powder metallurgy technique

ub lis he d by M an ey P ub lis hi ng ( c) IO M C om m un ic at io ns L td A mechanical powder metallurgy process involving a vibration stage before cold and hot compaction has been developed to manufacture functionally graded materials (FGMs). The microstructure and mechanical properties of p 2124 FGMs produced by this process have been studied. It was found that the vibration stage modified t...

متن کامل

Metallurgical Parameters Controlling the Eutectic Silicon Charateristics in Be-Treated Al-Si-Mg Alloys

The present work was carried out on Al-7%Si-0.4%Mg-X alloy (where X = Mg, Fe, Sr or Be), where the effect of solidification rate on the eutectic silicon characteristics was investigated. Two solidification rates corresponding to dendrite arm spacings (DAS) of 24 and 65 μm were employed. Samples with 24 μm DAS were solution heat-treated at 540 °C for 5 and 12 h prior to quenching in warm water a...

متن کامل

Mechanical Equation of State in an Al-Li Alloy

Existence of plastic equation of state has been investigated by performing a series of load relaxation tests at various temperatures using an Al-Li alloy. A plastic equation of state is first developed from a simple kinetics consideration for a mechanical activation process of a leading dislocation piled up against grain boundaries. A series of load relaxation test has been conducted at tempera...

متن کامل

Growth directions in directionally solidified Al–Zn and Zn–Al alloys near eutectic composition

Growth directions and crystallographic orientations of solidification microstructures have been measured in Al–Zn alloy near the eutectic composition. Al dendrites in Al–92 wt.% Zn alloy were found to grow along the h110i directions while Zn dendrites in Al– 96 and 98 wt.% Zn have h10 10i trunks. In the lamellar eutectic, a crystallographic relationship has been found between the dense plane of...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ژورنال

عنوان ژورنال: China Foundry

سال: 2022

ISSN: ['1672-6421', '2365-9459']

DOI: https://doi.org/10.1007/s41230-022-9003-2