AISI 316-L paslanmaz çeliğin yüzey işlemlerinde termo-kimyasal elektrolitik plazma teknolojisinin uygulanması
نویسندگان
چکیده
Yüzey özelliklerinin iyileştirilmesinde elektrolit olarak ara-yer elementlerinin kimyasal bağlı olduğu bileşikler saf su içinde çözündürülerek kullanılmıştır. Elektrolitler suda çözünebilen N (azot) ve C (karbon) gibi element içeren inorganik tuzlardan seçilmiştir. 3 farklı oluşturulmuştur. Birinci H2N-CO-NH2, ikincisi NH4NO3 esaslı Elektrolit/316 L ara yüzeyinde 300V daha yüksek gerilim uygulanarak enerjili plazma Yüksek iyonize olan elementleri 316L yüzeyine difüze olmuştur. Elektrolitik difüzyon işlemleri, çözeltiler kullanılarak 316 paslanmaz çelik altlık için gerçekleştirilmiştir. Plazma süresi 5 saniye ile 30 dakika arasında İşlemler sonucunda yüzeylerin N, O fazlardan oluştuğu, artan süreye mesafesinin sertliğin arttığı gözlenmiştir
منابع مشابه
Mechanical Properties of Boronized AISI 316, AISI 1040, AISI 1045 and AISI 4140 Steels
In this study, some mechanical properties of borided and unborided four steels were investigated. Boronizing of steels was performed by powder pack method at 1210 K for 4 h. The hardness of borides, boride layer thickness and room temperature tensile properties were measured and it was observed that hardness and tensile properties strongly depend on chemical composition of steels. In addition, ...
متن کاملPHASE TRANSFORMATION DURING WEAR OF AISI STAINLESS STEEL 316
Abstract: Austenitic stainless steels exhibit a low hardness and weak tribological properties. The wear behaviour of austenitic stainless steel AISI 316 was evaluated through the pin on disc tribological method. For investigating the effect of wear on the changes in microstructure and resistance to wear, optical microscopy and scanning electron microscope were used. The hardness of the worn...
متن کاملDynamic Strain Ageing and Eac of Deformed Nitrogen-alloyed Aisi 316 Stainless Steels
Intergranular stress corrosion cracking has occurred in BWR environments in non-sensitised, cold-worked austenitic stainless steel materials. The affecting parameters are so far not fully known, but deformation mechanisms may be decisive. The effect of cold deformation and nitrogen content on the deformation behaviour of austenitic stainless steels was investigated. The materials were austeniti...
متن کاملThe adhesion of hot-filament CVD diamond films on AISI type 316 austenitic stainless steel
Steel ball indentation and scratch adhesion testing of hot filament chemical vapour deposited diamond films onto AISI type 316 austenitic stainless steel substrates using two different interlayer systems, namely chromium nitride and borided steel, have been investigated. In order to compare the adhesion of these films with that of a well-known and strongly adherent system, detailed adhesion tes...
متن کاملSurface Texturing-Plasma Nitriding Duplex Treatment for Improving Tribological Performance of AISI 316 Stainless Steel
Surface texturing-plasma nitriding duplex treatment was conducted on AISI 316 stainless steel to improve its tribological performance. Tribological behaviors of ground 316 substrates, plasma-nitrided 316 (PN-316), surface-textured 316 (ST-316), and duplex-treated 316 (DT-316) in air and under grease lubrication were investigated using a pin-on-disc rotary tribometer against counterparts of high...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Journal of The Faculty of Engineering and Architecture of Gazi University
سال: 2021
ISSN: ['1300-1884']
DOI: https://doi.org/10.17341/gazimmfd.873709