AISI 304 Östenitik Paslanmaz Çeliğin Statik Yaşlanma Davranışının İncelenmesi
نویسندگان
چکیده
In this study, the change in material's mechanical properties by static strain ageing process after pre-deformation applied to AISI 304 austenitic stainless steel was investigated and analysed. The samples were first 5% then annealed oven at 150°C, 250°C, 400°C 550°C separate groups for 30 60 minutes. data obtained performing hardness tensile tests compared, interaction between test parameters these Pareto analysis. As a result of highest strength values observed minutes 150°C. yield strengths as-received material increased 10% with process. It determined that decreased from 400°C. addition, as analysis, it temperature value is most critical parameter affecting results.
منابع مشابه
Mechanical Characterization of Friction Welded AISI 304 Steels
There are many industries where austenitic stainless steel needs to be welded specially in power generation industries. Unfortunately the austenitic stainless welding has several fabrication and metallurgical drawbacks when welded by using conventional fusion welding methods, which can often leads to in-service failure. The most pronounced fabrication faults are hot cracks due to inadvertent us...
متن کاملEnhancement of corrosion protection of AISI 304 stainless steel by nanostructured sol–gel TiO2 films
0010-938X/$ see front matter 2013 Elsevier Ltd. All rights reserved. http://dx.doi.org/10.1016/j.corsci.2013.07.045 ⇑ Corresponding author. Address: Faculty of Mechanical Engineering and Naval Architecture, Departmet of Materials, Ivana Lučića 5, 10000 Zagreb, Croatia. Tel.: +385 1 616 8313; fax: +385 1 615 7126. E-mail address: [email protected] (L. Ćurković). Lidija Ćurković a,⇑, Helena ...
متن کاملDesign optimization of cutting parameters for turning of AISI 304 austenitic stainless steel using Taguchi method
In the present work Taguchi method is used to optimize cutting parameters during dry turning of AISI 304 austenitic stainless steel with AlTiCrN coated tool. The coating was deposited on fine-grained K-grade (ISO K-20) cemented carbide cutting insert using physical vapor deposition (PVD) technique. The turning parameters evaluated are cutting speed of 200 and 260 m/min, feed rate of 0.20 and 0....
متن کاملA Cohesive Zone Model for Crack Growth Simulation in AISI 304 Steel
Stable ductile crack growth in 3 mm thick AISI 304 stainless steel specimens has been investigated experimentally and numerically. Multi-linear Isotropic Hardening method coupled with the Von-Mises yield criterion was adopted for modeling elasto-plastic behavior of the material. Mode-I CT fracture specimens have been tested to generate experimental load-displacement-crack growth data during sta...
متن کاملSome Studies on Temperature Distribution Modeling of Laser Butt Welding of AISI 304 Stainless Steel Sheets
In this research work, investigations are carried out on Continuous Wave (CW) Nd:YAG laser welding system after preliminary experimentation to understand the influencing parameters associated with laser welding of AISI 304. The experimental procedure involves a series of laser welding trials on AISI 304 stainless steel sheets with various combinations of process parameters like beam power, beam...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Karadeniz fen bilimleri dergisi
سال: 2022
ISSN: ['1309-4726', '2564-7377']
DOI: https://doi.org/10.31466/kfbd.1072474