3D Printed Enzyme‐Functionalized Scaffold Facilitates Diabetic Bone Regeneration
نویسندگان
چکیده
Adv. Funct. Mater. 2021, 2101372 DOI: 10.1002/adfm.202101372 In the originally published article, local magnification images for Alg/CaP group were found to be unmatched in Figure 7B. The corrected image is shown below. overall conclusions from these figures, as well paper, are unaffected. major organs (heart, liver, spleen, lungs, and kidneys) of rats after implantation Alg/GOx Alg/GOx/[email protected] scaffolds 2 months analyzed using H&E staining. There no significant differences between control GOx contained groups, indicating long-term biosafety vivo. original lung was repeatedly clipped used again S12 (Supporting information) error. As neither show differences, this figure, authors apologize any inconvenience caused.
منابع مشابه
A 3D-printed scaffold with MoS2 nanosheets for tumor therapy and tissue regeneration
The treatment of malignant bone tumors is a significant clinical challenge because it requires the simultaneous removal of tumor tissues and regeneration of bone defects, and bifunctional three-dimensional (3D) scaffolds that function in both tumor therapy and tissue regeneration are expected to address this need. In this study, novel bifunctional scaffolds (MS-AKT scaffolds) were successfully ...
متن کامل3D Printed Anatomical Nerve Regeneration Pathways.
An imaging-coupled 3D printing methodology for the design, optimization, and fabrication of a customized nerve repair technology for complex injuries is presented. The custom scaffolds are deterministically fabricated via a microextrusion printing principle which enables the simultaneous incorporation of anatomical geometries, biomimetic physical cues, and spatially controlled biochemical gradi...
متن کاملAdvanced Nanocomposite Scaffold for Bone Regeneration
Introduction Each year in the United States approximately 500,000 procedures that involve the use of bone substitutes are performed. To address the limitations of materials currently used in orthopaedic tissue engineering, we have developed novel nanocomposite materials that consist of a citric acid-based elastomer, poly(1,8 octanediol citrate) (POC) and bioceramic nanoparticles, βtricalcium ph...
متن کاملAbstract: Dipyridamole Releasing 3D Printed Bioactive Ceramic Scaffolds with Osseoconductive Geometries Promote Craniofacial Bone Regeneration
METHODS: Custom 3DPBC scaffolds designed to present lattice-based porosity only towards the dural surface were either coated with collagen (control) or coated with collagen and immersed in a 100 μM concentration dipyridamole (DIPY) solution. Sheep (n=5) were subjected to 2 ipsilateral trephine-induced (11 mm diameter) calvarial defects. Either a control or a DIPY scaffold was placed in each def...
متن کاملEffects of 3D-Printed Polycaprolactone/β-Tricalcium Phosphate Membranes on Guided Bone Regeneration
This study was conducted to compare 3D-printed polycaprolactone (PCL) and polycaprolactone/β-tricalcium phosphate (PCL/β-TCP) membranes with a conventional commercial collagen membrane in terms of their abilities to facilitate guided bone regeneration (GBR). Fabricated membranes were tested for dry and wet mechanical properties. Fibroblasts and preosteoblasts were seeded into the membranes and ...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Advanced Functional Materials
سال: 2021
ISSN: ['1616-301X', '1616-3028']
DOI: https://doi.org/10.1002/adfm.202106571